Program za flashanje grafe

Pa še neki. Vidu sm nek članek pa je majstr naviu grafo tok kot jaz pa je neki računau za frekvenco rama 1000/4 (kao da ma 4ns rame (kot jaz)) torej da več kot 250 MHz ram ne bo šou. A je to res? Pa dejte pliz navest še kšn program.

Kaj pa so še neki ATI Flash, a je ta boljši?
Pa še tusti BiosEdit me malo jebe.

VASkO, najlepša ti dala!!!

----- Flashrom 2.23 Help -----
Format: FLASHROM [command] [parameter1] [parameter2] [parameter3] < option/ s >
[command]:
-i Display information of ATI PCI adapters in the system.
-p < Num > < File > [r] Write BIOS image in file < File > to flash ROM in Adapter
< Num >. Reboot after write if [r] flag is specified
-pm < Num > < File > [r] Write BIOS image for MAC
-pi < Num > < File > [r] Write inverted BIOS image for R200 Parallel ROM
-pa < Num > < File > [Loc] Write BIOS image in file < File > to flash ROM in Adapter
< Num > starting from specific location [Loc] in Hex.
-s < Num > < File > [Size] Save BIOS image from adapter < Num > to file < File >.
First [Size] kbytes of ROM content is saved if [Size]
is specified.
-cf < File > [Size] Calculate CRC for file < File >.
CRC for the first [Size] kbytes of the file is
calculated if [Size] is specified.
-cb < Num > [Size] Calculate BIOS image CRC for adapter < Num >.
CRC for the first [Size] kbytes of the ROM content is
calculated if [Size] is specified.
-cr < Num > [Checksum] Calculate 16-bit ROM checksum for adapter < Num > and
compare it to the [Checksum] specified.
-l < Num > Check whether the ROM of adapter < Num > is currently
locked or unlocked.
< option/s >:
-f Force flashing regardless of security checkings (e.g.
AsicID & BIOS file info check OR boot-up card).
-bndn read bus# & device# from 'bndn.ini' file.
-d Display debug informations.
< tvstd option/s >:
NTSC sets the default BIOS built-in initialization standard.
PAL Usage: -p < Num > < File > < tvstd option >
PAL_M
PAL_60
NTSC_J
SCART_RGB
PAL_CN
PAL_N
*< Num > = adapter number, < File > = filename, [Size] = data block size in KBytes
*Use command -i to see the adapter numbers in the system.

Torej WTF!?!?

Kako naprej? Frekvence v Radedit sm naštimau, bios shranu, tanowga in tastarga, ko pa poženem flashrom mi odpre konzolo za kako sekundo potem pa nič. Če prav razumem, morš ob zagonu držat določeno tipko al kaj?

Če jst prov razumem bi ti rad zdej sam flashal? Najpraj nared boot disketo in dej gor flashrom (vse file). Pol bootej iz diskete in napiš: flashrom -s 0 original.bin da boš spravu tastarga če gre kej narobe. Pol pa napiš: flashrom -p 0 imeodfila.bin (vstavi ime od filea ki si ga spremenil. In to je to.
B

Se mi je zdelo mal čudno, ja da bi kar z winsov, bom zdaj probal flashat.

CAS pusti.
Jaz sem dal na svoji CAS 1 ni bilo nic bolje, medtem ko sem dal na CAS3 mi je totalka zjebalo (artefakti ze takoj pri stetju RAMa).
Sem moral po obcutku potem flashat ker se ni nic videlo na monitorju