Zdej pa res ne vem ... RAID ????

si mogoče pomislu, da sta na teh dveh platah različna raid kontrolerja?

pa si ... mogoče ... pomislu ... da bi namest ... inflacije pik ... uporabu kako ... vejico... ali pa samo ... eno piko?

Pa kdaj se bote naučili, da RAID polja ne moreš kr prestavit na drug kontroler? Za postavitev polja pa si preberi navodila od plate. Podatke pa najprej spravit v en backup na stari plati (če jo še maš). Drugače bo panika.

Ja itaq, sam sem vseeno zrihtal, dal sem v prejšnji računalnik in je bilo še vse gor
Ampak, vseeno problem .. sploh ne morem na novo postavit RAID-a ... vse naredim točno .. ampak ko hočem narediti particije v WIN - ob inštalaciji .. sta 2 diska in ne en ????

In ... kako se prav naredi ?? Ali kdo ve ??

Sej, pa ni tako, očitno tale plata neki ne deluje dobro ali pa ne naredim kaj prav.
V Biosu določiš, kje hočeš imeti raid - recimo na SATA 3 in 4 ... OK
Potem shraniš nastavitve in zaženeš računalnik ... pred bootom te da opcijo F10 za postavitev RAID-a .. tam določiš NAČIN RAIDA (Striping) in določiš diska.
Nato ti reče še, da moraš zbrisat podatke na njih in daš Yes!!
Iz menija ven moraš pritisniti Cintrol in X ... nato se mašina spet buta na CD ... določiš
gonilnike z F6 za SATA in RAID ... vse lepo in prav.
Ko pa se pokaže particija diskov, kjer jih moraš če pač hočeš formatirati, no tuki pa rata
problem ... enostavno sta še vedno 2 diska z po 120GIGA in ne sam 240GIGA ???
Kje bi lohk bila napaka?
In kaj pomeni BOOT 1 ali 2 v nastavitvah za RAID?? ker to lohk določiš .. sicer se nič ne spremeni!!

in OČITNO nisem edini !!!!

http://www.xtremesystems.org/forums/arc...

Hi guys, I'v got everything set up, and I'v been sitting here for a bit over 2½ hours trying to get RAID going. The problem is that after I'v installed the 2 nvRAID drivers using WinXP's F6 to install 3rd Party..... in the XP installation. XP installation still tells me that I have two seperate SATA drives (Seagate 120GB 7200.7)

Here's what I'v already done, and my sata related BIOS settings, if you spot anything wrong with them, plz tell me what. And if you want some info on other BIOS settings, just ask.

BIOS is v. 218
Advanced BIOS Features:
Hard Disk Boot Priority: 1: SCSI-0 : nVidia Stripe 223.58G (2: is bootable add.)
CD-ROM Boot Priority: 1. Ch1 M : Samsung DVD-ROM SD-616Q
First Boot Device: CDROM
Second Boot Device: Hard Disk
Third Boot Device: Hard Disk

Integrated Periphearals:
RAID Config->
RAID Enable: Enable
Internal Phy SATA 3 RAID: Enable
Internal Phy SATA 4 RAID: Enable
Internal Phy SATA 2 RAID: Enable
Internal Phy SATA 1 RAID: Enable

Genie BIOS Setting:
Internal Phy SATA 1/2: Enable
Internal Phy SATA 3/4: Enable

I'm running 1 stick of 512MB Corsair XMS3500C2 Rev1.1 (BH-5) in DIMM2 (suggested by other people around the net), and not both of my sticks for Dual Channel.

In Raid Setup Utility, I'v created an array with both drives (as you can from Hard Disk Boot Priority), it's a Striping Array with a block size of 64kb. Both drives have been cleared using the Raid Utility, and made Bootable.

In XP install, I press F6 to install 3rd Party drivers, and when it prompts me for them, I choose and install both drivers from the disk. I even tried downloading the MSI NF4 drivers and using them, but still XP install does not recognise my array, but instead just two seperate drives....

Thats what I'v done for now... Ofcourse I'v played around with the BIOS settings, SATA ports (using 3/4 right now), another XP CD (I have a normal and one with SP1 slipstreamed).

If you can help me, please do so! I'm getting desperate go get this thing going.

System specs for good messure:
3200+ Winchester
DFI NF4 Ultra-D
2x 512mb Corsair XMS3500C2 (using only 1 right now)
2x Seagate SATA 7200.7 trying to get RAID0 going.
PowerColor X800XL

No sound card installed yet (Audigy2), and I'm not using the AC97 sound module, the onboard sound is disabled in BIOS.

START
PROGRAMI
PRIPOMOČKI
SISTEMSKA ORODJA
SISTEMSKE INFORMACIJE

in na desni strani ti prikaže različico biosa