Print - ethernet kabel

Rabiš

1)Printer z mrežno kartico
ali
2) Router z usb priključkom, ki deluje kot print server ( med cenejšimi na bolhi je CN-BR1)
ali
3.) Print server

printerju daj nek ip iz nabora ki ga imas v omrezju, gres v winsih pod dodaj tiskalnik vpises tcpip i to je to

ameba je 11. maj 2011 ob 12:36 izjavil:

Printer povež v router z mrežnim kablom, ta mu bo dodelil nek IP in ti se povež na printer preko routerja oz. lokalno....

A se da to narediti BREZ RUTERJA, kabel direktno v printer ?

Hvala za pomoč, ampak to ni to:
na tvojem linku piše sledeče:

•Step 4
Look on the status page that you printed earlier for a line that says "IP address." Every ethernet printer that is connected to a network will have one. Once you've found that, input that number on the IP address line. Click "Next," then "Finish."

To je tudi moje problem pri googlu da mi da vse zadetke, ki dajejo navodila kako naredit prinanje preko mreže, ne pa direktno samo z kablom. Ne vem kakšen search string naj dam, ga bo v redu :-(.

A drgač si že probu povezat, pa da vidš kaj se zgodi ?

Če hočeš kakšen bolj konkreten odgovor, bi lahko navedel model tvojega tiskalnika in OS-ja.

Drugače pa če tiskalnik podpira, mu nastavi fiksni IP naslov,
nato ta IP daš pod izbiro omrežnega tiskalnika.

RTFM!!!

Iz navodil za P2050 serije:

Use this menu to establish network configuration settings.
Menu item Description
CFG TCP/IP Access the TCP/IP menu and set TCP/IP protocol parameters.
? BOOTP=YES* Enable IPv4 configuration by a BOOTP Server.
? DHCP=YES* Enable IPv4 configuration by a DHCP Server.
If DHCP=YES* and the print server has a DHCP lease, you can configure the following DHCP
settings:
? RELEASE: Select whether to release (YES) or save (NO) the current lease.
? RENEW: Select whether to renew (YES or NO) the lease.
AUTO IP=YES* Automatically assign a link-local IPv4 address in the form 169.254.x.x.
If you specify BOOTP=NO*, DHCP=NO* and AUTO IP=NO*, you can manually set the following
TCP/IPv4 parameters from the control panel:
? Each byte of the IPv4 address (IP)
? Subnet Mask (SM)
? Syslog Server (LG)
? Default Gateway (GW)
? Idle Timeout period (default is 270 seconds, 0 disables the timeout)
CFG DNS 1: IPv4 address of a primary DNS server (one byte at a time).
CFG DNS 2: IPv4 address of a secondary DNS server (one byte at a time).
IPV6 = YES*: Enable IPv6 operation. Select NO to disable IPv6 operation.
POLICY=RTR_AV/RTR_UN/ALWAYS: Set one of the following IPv6 addressing policies:
? RTR_AV: (default) Stateful auto-configuration method is determined by a router. The router
specifies whether the print server obtains its address, configuration information, or both from
a DHCPv6 server.
? RTR_UN: Attempt to obtain stateful configuration from a DHCPv6 server (when a router is
not available).
? ALWAYS: Always attempt to obtain stateful configuration from a DHCPv6 server (whether
or not a router is available).
MANUAL= KEEP/DISABLE: Set the behavior of a manually configured IPv6 address detected on
the print server.
? KEEP (default): Maintain the address in an active state.
? DISABLE: Maintain the address but in an inactive state.
Print an HP Jetdirect configuration page to verify your settings. (The print server can overwrite
selected parameters with values that ensure proper operation.)



Edit RTMF v RTFM ;)