ATI, X.org in tv out

Kako bi popravil RBG za TV-out? Če dam na clone, mi nabije preveč rdeče in ne morm spreminjat RGB (sam prek ukaza, kar je pa mučno). Če pa dam, d uporablja dva driverja (en za TV in en za monitor) pa ne znam menat med screeni. (nardi dva ločena desktopa in z enega desktopa ne morm premikat na drugega)

Hvala vnaprej,
MasterMind


[ Odgovori in brisi 'gumba' sta prevec skupaj... ;) -- BigW ]

Hvala.. Sm uporabi ATI-jeve driverje, d mi nardi xineramo. Zdej pa morm Qt rekompajlat s podporo za xineramo .

Hvala..

Ce naredis dual head konfiguracijo, potem se na drug ekran preselis samo z premikanjem miske. ;) Ne mores pa vlect aplikacij sem ter tja... Zal. Vsak. Prednost tega je, da lahko vsak screen poganja svojo locljivost.

Config gre pa nekako takole: (samo relevant sections...)

Section "Monitor"
Identifier "Monitor0"
HorizSync 31.5 - 80.5
VertRefresh 20 - 60
Option "DPMS"
EndSection


Section "Monitor"
Identifier "TV"
HorizSync 30-50
VertRefresh 60
EndSection

Section "Device"
Identifier "ATI Graphics Adapter connector 0"
# Driver "radeon"
Driver "fglrx"
...
BusID "PCI:2:0:0" # vendor=1002, device=4e48
Screen 0
EndSection

Section "Device"
Identifier "ATI Graphics Adapter connector 1"
Option "VideoOverlay" "on"
# Driver "radeon"
Driver "fglrx"
BusID "PCI:2:0:0" # vendor=1002, device=4e48
Screen 1
EndSection

Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter connector 0"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"

Subsection "Display"
Depth 24
Modes "1280x1024"
ViewPort 0 0 # initial origin if mode is smaller than desktop
EndSubsection
EndSection

Section "Screen"
Identifier "Screen1"
Device "ATI Graphics Adapter connector 1"
Monitor "TV"
DefaultDepth 24
#Option "backingstore"

Subsection "Display"
Depth 24
Modes "800x600"
ViewPort 0 0 # initial origin if mode is smaller than desktop
EndSubsection
EndSection

Section "ServerLayout"
Identifier "Server Layout"
Screen "Screen0"
Screen "Screen1" RightOf "Screen0"
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
Option "Xinerama" "off"
Option "CloneDisplay" "off"
EndSection


Tole meni prav lepo deluje... In sem zadovljen s setupom... Poleg tega KDE zelo lepo podpira dual screen setup...

Sam kaj mi bo to pomagal, če je TV v drugi sobi? Morm pol za vsak milimeter premika miške it tečt pogledat na TV... (no go)

Odpreš terminal (v KDE npr Alt+F2 in vpišeš *term) in na slepo napišeš tisti bogi ukazek za mplayer ;)

I tegale košča:
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
Option "Clone" "off"
Option "Xinerama" "on"
Screen "Screen[0]" RightOf "Screen[1]"
Screen "Screen[1]"
EndSection
sklepam da ima Option Clone nekaj veze s tvojim problemom.

Saj je iz dneva v dan slabse... :) Ker se obrablja mrezica na kateri se ustvarja slika.